Package Includes: Pair Headlight Assembly Left + Right. Features: Plug and Play Operation, Direct Bolt-On OE Fitment or Replacement for the Stock Unit Comes with a Complete Set of Headlights (Driver and Passenger Side) Brings a Different Appearance to Vehicle thats Great for Show Use or to Replace Old and Worn Headlights Requires no Modification or Drilling. Pair Headlight Assembly Left + Right.
Plug and Play Operation, Direct Bolt-On OE Fitment or Replacement for the Stock Unit Comes with a Complete Set of Headlights (Driver and Passenger Side) Brings a Different Appearance to Vehicle thats Great for Show Use or to Replace Old and Worn Headlights Requires no Modification or Drilling. Waterproof:The whole sealing construction can prevent moisture from entering the inside of housing. Dust proof:The full sealed design will prevent the ingress of rain, dust and other foreign matter.
Heat Dissipation:With efficient heat dissipation, the construction of headlight will be protected and its useful life will be extended. DOT/SAT approved for street legal. For toughness, impact resistance, and heat resistance. Condition: 100% Brand New and High Quality 5.Material: ABS Plastic Housing / Polycarbonate Lens 6.100% Brand New! Professional Installation is Highly Recommended. Installation Instruction is NOT Included. Undo the screws, clips, or retainer springs that hold the headlight in place. Disconnect the wiring from the assembly. Detach the headlight from the vehicle to replace it with a new one. Fit in the new headlight assembly. Fix the new headlight into place and make sure that the screws, clips, or retainer springs used are sealed.
Reconnect the wiring that was unplugged from the assembly. Put back the grille and other components that you removed. Seal them back into place.
Before you begin to adjust the light, make sure check the alignment of your lights first. Park the vehicle about 10 to 25 feet from the wall with the lights aimed at the wall. The centerlines of the headlights should not be any higher than 3.5 feet above the ground.Firstly, locate the adjustment screws on your vehicle. The headlights should be adjusted one at a time. Put a rag or towel over a chair in front of the light you want to block. Covering the light assembly directly can damage the plastic lens. The screw on the top of the light housing should be turned clockwise to raise the lights and counterclockwise will lower the light.
The headlight should be adjusted until the top of the most intense part of the light beam shines directly on or just below the center of the tape line on the wall. The screw on the side of the light housing should be turned to get the right/left adjustment correct. Adjust the lens so that the most intense part of the beam is to the right of the vertical line.
12V Universal Low Pressure 5-9 PSI Electric Fuel Pump Installation Kit E8012S. Pair Front Or Rear Wheel Hub Bearing For Chevy Impala Pontiac Grand Prix Venture. Front Or Rear Wheel Bearing Hub For Buick Rendezvous Lesabre Chevrolet Impala. Rocker Pannel & Cover Trim.
RV & Golf Power Cord. Nerf Bars And Running Boards. Front Bumper Lip Splitter Stru.
Car Window Film Tint Tools. Struts & Suspension Kit & Hubs.Leveling kit + struts shocks. Drive Shaft And Half Shaft.
C Notch & Flip Kit. 4 Pcs Wheel Hub Bearing. Power Steering Pump & Parts.
Hydraulic Lifter & Rocker Arms. Fuel Tank Valve & Regulator. Fuel Tank Pipe & Cap. Engine Gasket & Cylinder Head. 2pcsX New Upstream Downstream Oxygen Sensor 02 O2 for 1996 Buick Skylark 3.1L.
ECCPP 11Pc Complete Power Steering Rack And Pinion Suspension Kit For Chevy Gmc. 4X Oxygen o2 02 Sensor and Mass Airflow Sensor for 2000 GMC K2500 Sierra 7.4L. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts & Accessories\Lighting & Lamps\Headlight Assemblies". The seller is "eccppautoparts" and is located in this country: US.
This item can be shipped worldwide.